• Square Mixing Tip
  
• 4" Long
  
• Case of 10

Add-A-Snap - White - 1-1/2" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Add-A-Snap - Black - 2-1/2" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Add-A-Snap - White - 4" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

Add-A-Snap - Black - 4" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Stainless Steel Bottle Opener with Brushed Finish 

Corrosion resistant investment cast 316 stainless steel bottle opener wall mounts with two #6 FH fasteners (not included).

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Plastic Suction Cup Handle

Injection Molded Nylon/Nitrile-Buna Rubber 

Portable, dual suction cup handle installs instantly. Mounts in any direction on any non-porous surface. Easily mount and re-mount with no marks or damage to hull. No holes, screws, or tools required. Ideal for cleaning waterlines or boat bottoms while swimming or from a dinghy. Attach to your paddleboard or kayak for an extra handle during transport. For use above or below the waterline. Constructed of non-corrosive injection molded nylon and Nitrile-Buna rubber. Designed to assist grip not to leverage full body weight.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Add-A-Snap - White - 2-1/2" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Emergency Deck Fill Plug

Nitrile-Buna Rubber

This Emergency Deck Fill Plug is a must for any vessel. Fits most 1-1/2" hose deck fills in the event you lose your cap. For temporary use only until you can replace your OEM cap. Constructed of fuel resistant Nitrile-Buna rubber.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

• AT-8040 Adhesive
  
• (25) Pieces AT-5 White Tie Mount
  
• (1) Plastic Mixing Sheet
  
• (2) Mixing Sticks
  
• Complete step-by-step instructions

8040 Acrylic Adhesive with Plunger 

CANNOT SHIP AIR - UPS GROUND ONLY

AT-8040 is a good general purpose adhesive packaged in a manual plunger cartridge. Simply snip off the two end caps and dispense the needed amount of adhesive onto a clean surface and mix it by hand. AT-8040 cures in 10-12 minutes, has a 6 minute working time and develops working strength in 40 minutes. AT-8040 has a 12 month shelf life when stored at 72°. Weld Mount recommends that where ever possible this adhesive be refrigerated. Packaged in a 30ml cartridge this adhesive does not require the adhesive gun or mixing tips. The 30ml cartridge will bond 30-50 parts.

Add-A-Snap - Black - 1-1/2" 

For use with canvas or nylon boat covers, the Add-A-Snap allows you to easily add length on hard to reach snaps from shrunken material. Nickel plated brass/nylon.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

• Square Mixing Tip
  
• 4" Long
  
• Case of 50

• Revolutionary Adhesive
  
• Parts Stay Where Placed Without Sliding
  
• For Use Overhead and on Vertical Surfaces
  
• No Need for Fixtures