DC 105 CFM Flangemount 3" Blowers
Jabsco blowers are primarily intended for intermittent duty cycles such as evacuating fuel vapors from bilge areas. If desired, they also may be used for other general air circulation applications with longer duty cycles. However, when doing so, it should be noted that the maximum motor life is approximately 1000 hours. Therefore, the blower should only be used for applications if this length of service is acceptable. Features:
|
Blower with Variable Speed Control for Use With Ventis HES170 and HES240.
|
Blower with Variable Speed Control for HES140
|
YELLOWTAIL™ 3" Marine Blower - 12 VDC, 120 CFM
SHURFLO has developed a unique nylon fan that includes six blades to ensure high performance and efficient ventilation for bilges, engine compartments, galleys and heads. Installation of the YELLOWTAIL blower is made easy with extended barbs and slotted mounting bracket. Features:
|
Flexmount Blower
High volume air intake or extraction blowers for engine room, fuel compartment, galley or heads Features:
|
AC 100 CFM Flangemount 3" Blowers
Features:
|
YELLOWTAIL™ 4" Marine Blower - 12 VDC, 215 CFM
SHURFLO has developed a unique nylon fan that includes six blades to ensure high performance and efficient ventilation for bilges, engine compartments, galleys and heads. Installation of the YELLOWTAIL blower is made easy with extended barbs and slotted mounting bracket. Features:
|
Turbo 3000 Series In-Line Blower
Part #: 1733-4 The first vane axial-flow fan bilge blowers designed using aerospace technology to maximize performance. No other bilge blowers in the industry provide such powerful system output at such a low power input in a compact size. Patented in-line design - provides ventilation for engine compartments, galleys, bilges, and heads. Mounting feet allow vertical or horizontal installation in confined spaces. Install with #10 fasteners. Individual carton includes 2 tie straps. All are CE certified. 16-gauge tinned and caulked copper wire leads with optional MP1 molded rubber connectors. Improved 3" design. Features:
|
4" In-Line Blower
Inlet/Outlet - 4" CFM - 240
|
DC 150 CFM Flexmount 3" Blowers
Features:
|
Rule In-Line Blower - 3" Ducting
Part Number: 140 Designed for efficient, high output operation, these blowers feature our exclusive front and rear shaft seals and corrosion resistant motor housings for long life. Compact and easily installed on any flat surface, Rule? in-line blowers provide higher air flow, lower amp draw, and quieter operation than standard blowers. For International & US Markets. Features
Applications: Race cars and helmet ventilation Bus ventilation (engine and bathroom fumes) Prison van ventilation (cooling, air-freshening) Blow-up signs and mascots Tanning booths Building ventilation Specifications
|
Flexmount Blower
DC 150 CFM Flexmount 3" Blower
|
3" In-Line Blower
Inlet/Outlet - 3" CFM - 158
|
DC 250 CFM Flexmount Continuous Duty 4" Blowers
Features:
|
DC 250 CFM Flangemount 4" Blowers
Features:
|
Turbo 4000 Series II In-Line Blower
Part #: 1749-4 Attwood's improved Turbo 4000 Series II sets the standard for in-line blower performance. Utilizing advanced fan blade design techniques, Attwood has developed a blower system that matches air flow of existing in-line blowers at a significantly reduced noise level. The first vane axial-flow fan bilge blowers designed using aerospace technology to maximize performance. No other bilge blowers in the industry provide such powerful system output at such a low power input in a compact size. Patented in-line design - provides ventilation for engine compartments, galleys, bilges, and heads. Mounting feet allow vertical or horizontal installation in confined spaces. Install with #10 fasteners. Individual carton includes 2 tie straps. All are CE certified. 16-gauge tinned and caulked copper wire leads. Features:
|
Flangemount Blower
DC 250 CFM Flangemount 4" Blower
|
Heavy Duty Flexmount Blower
DC 250 CFM Flexmount 4" Blower
|
Heavy Duty Flangemount Blower
Heavy Duty Blowers are designed for applications such as commerical or high use engine room ventilation and extraction where a long life requirement demands heavy duty motors with long brush life. Built to provide the same high outputs as our standard specification blowers.
|
Heavy Duty Flexmount Blower
DC 250 CFM Flexmount Continuous Duty 4" Blower
|
Heavy Duty Flexmount Blower
AC 250 CFM Flexmount Continuous Duty 4" Blower Flexmount Blowers are built to the same high specification as the Heavy Duty Flangemount Blowers for use as air intake or extraction systems in engine rooms, fuel compartments, galleys or heads.
|
Rule In-Line Blower - 4" Ducting
Part Number: 240 Designed for efficient, high output operation, these blowers feature our exclusive front and rear shaft seals and corrosion resistant motor housings for long life. Compact and easily installed on any flat surface, Rule® in-line blowers provide higher air flow, lower amp draw, and quieter operation than standard blowers. For International & US Markets. Features
Applications: Race cars and helmet ventilation Bus ventilation (engine and bathroom fumes) Prison van ventilation (cooling, air-freshening) Blow-up signs and mascots Tanning booths Building ventilation Specifications
|
Air Blower 1000 In-Line 250 - 12V 7″ in-line mounted marine ventilation 12V axial blower with capacity 1000 m3 per h, 589 CFM. 178mm port connection and 250mm length. Sheltered blades from blower housing interference at tough installation. Compact 5 blade design to maximize performance. For continous duty. 7A fuse. Interchangeable with Vetus Vent17812A. Features:
|
Air Blower 1000 Inline 165 - 12V 7″ in-line mounted marine ventilation 12V axial blower with capacity 1000 m3 per h, 589 CFM. 178mm port connection and 165mm length. Sheltered blades from blower housing interference at tough installation. Compact 5 blade design to maximize performance. For continous duty. 7A fuse. Features:
|
Marine Air Blower 500 Flange - 12V 4″ flange mounted marine ventilation 12V radial blower with capacity 500 m3 per h, 324 CFM. Inlet 100mm, outlet 103mm. Body in hermoplastic PA6 high durable white Nylon with integrated blower motor. 12A fuse. Interchangeable with Johnson Pump 80-47417-01. Features:
|
Marine Air Blower 750 Flange - 12V 6″ flange mounted marine ventilation 12V radial blower with capacity 750 m3 per h, 441 CFM. Inlet 150mm, outlet 103mm. Body in hermoplastic PA6 high durable white Nylon with integrated blower motor. 10A fuse. Interchangeable with Johnson Pump 80-47418-01. Features:
|
3" Blower Flange Mounted - 12V Features:
|
Enhance your back or front yard decor with this stunning stepping stone! Perfect for marking pathways and flower beds as well as decorating vegetable patches and ponds, this garden accent will bring charm and appeal to any space. Simply place in the desired location to add a personalized touch to the outdoors!
|
5" X 5" Extra-Quiet Black Circulator Fan mounts high in a doorway or hallway to move warm air out of one room into another. Its swivel bracket allows directed air flow. It has a 12 ft. plug-in cord with one speed. 105 CFM.
|
W320-0011 Blower Guard, Required When Using Blower
This item cannot ship to APO/FPO addresses. Please accept our apologies. |
|
|
|
|
|
|
Copyright © 1999-2022 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |