|
*EACH* Street Vision Diffusional Photo Shield License Plate Covers
Protect your custom license plates from weather damage with these high end deflective plate covers. Save Money against Traffic Tickets |
Keep the front of your Jeep looking factory new! Great for dressing up the dull area between the front bumper and Grille. Some drilling may be required. Made of durable plastic and is black in color. Says Jeep on front.
|
If you have a winch and fairlead mounted to the front of your vehicle, there's nowhere to put your license plate. With Smittybilt's license plate holder you just mount you license plate to the holder and snap it on your roller fairlead, and once again your street legal.
For 4 way roller fairlead
No drilling installation
|
The JK Rear License Plate Delete Cover snaps into the hole left behind when deleting the stock JK rear license plate mount. This could be useful for those running a Poison Spyder Tramp Stamp or aftermarket rear bumper that relocates the license plate. It is not needed if using Poison Spyder Crusher Corners, as they will cover the hole. Made of black, textured, molded plastic.
Fits 2007 to 2014 JK Wrangler, Rubicon and Unlimited
2 and 4-door models
Black
Molded plastic
|
BRASS PLATED GOLD NUGGET LICENSE FRAME
|
CHROME CHAIN LINK LICENSE FRAME
|
BARJAN 8 BALL LICENSE PLATE FASTENERS
|
GOLD DEL RAY LICENSE FRAME
|
NEW YORK GIANTS LICENSE PLATE
|
The Poison Spyder JK License Plate Mount allows you to relocate your Jeep's license plate to the center of the tailgate, for those who run without a tailgate-mounted spare tire. The License Plate Mount uses four of the OE spare tire mount bolts, and is offset to allow proper function of the tailgate vents. If using this item to relocate the license plate, we recommend using the Stock License Plate Delete Cover # PSC17-04-112 to fill the hole where the factory license plate mount was located. NOTE: This item was designed to fit JK's with the wide vent on the tailgate (vent is wider than it is tall). These are generally found on 2010 and newer JK's, however they have also been found on some 2009's. This item may also be used on JK's with the tall tailgate vent (taller than it is wide), which were typically found on 2007-2009 JK's, however the edges of the vent may still be visible above and below the license plate.
Fits 2007 to 2014 JK Wrangler, Rubicon and Unlimited
2 and 4-door models
Black powder coat
Designed for "wide vent"
|
Keep your Jeep legal with Smittybilts license plate bracket. Clamps onto any 3" tube. Includes all mounting hardware needed.
Universal application
Fits all 3" tubular bumpers
Clamp on, no driling required
|
Keep your rig street legal with this license plate light mount from Smittybilt. Relocate your license plate to center of your spare tire;Easy install, no drilling;Works with aftermarket and OE tire carriers;Includes 2 light mount holes;Satin black powder coat;5 year finish warranty
|
Give your tube bumper that finished look with this front frame cover. Made to fill the gap in between the bumper and frame. Finished in textured black, it compliments any front tube bumper.
|
LICENSE PLATE HOLDER 48 X 9" 1/BX
|
MINNESOTA VIKINGS LICENSE PLATE
|
A perfect way to relocate your license plate while adding a custom look, this License Plate Bracket is constructed of 14-gauge HRPO steel plate and comes complete with all of the mounting hardware for an easy installation. With a base plate mounted behind your hawse style fairlead, your license plate is quickly removable by unscrewing two lobed knobs. Dimpled holes in the license plate mount keep the bracket rigid and a stamped WP is readable from the backside when the license plate is installed.
Fits 1955 to 2012 Wrangler and CJ
Black powder coated
Constructed of 14-gauge HRPO steel plate
Hawse fairlead bracket
License plate bracket
2 lobed knobs
Mounting hardware
|
The Perfect solution for those off road bumpers! Now you can run that great off road bumper without drilling for a front license plate mount! This easy to use clamp on license plate mount secures to your winch roller fairlead using heavy duty steel clips. To remove for winching, simply give it a hard tug. To replace, just clamp on! The front plate portion is pre-drilled and tapped and includes heavy duty mounting screws for your license plate. Fits all standard roller fairleads. Comes pre-assembled ready for use.
Fits all standard roller fairleads
Clamp on design
Removable for winching
Includes mounting screws for license plate
|
BOY/GIRL FRIEND FRAME
|
For use with Ultimate Bull Bar and E-Series Bull Bars
Black powder coated
Stamped formed steel
5 year warranty
|
LICENSE FRAME
|
Is your license plate bracket cracked or missing? This replacement license plate bracket is dependable and matches OE form, fit and function to keep your plate in plain view.
|
If your state requires a front license plate, we have a solution for you. Instead of drilling holes in your bumper or risking not running a front plate, this easy to install license plate holder attaches to your winch fairlead. Simply bolt your license plate to the bracket and snap the holder in place. Your license plate is now securely mounted yet easily removable for winching.
License Plate Bracket
Front
Fairland License Mounting Bracket
|
This factory-style replacement license plate bracket from Omix-Ada has a black powder coated finish to prevent rust. Fits 87-95 Jeep Wrangler YJ.
|
LICENSE FRAME
|
TAG RELOCATION BRACKET
|
BRACKET LICENSE PLATE
|
BACK-UP CAMERA LICENSE
|
Jeep JK License Plate Mount Cover and Bottle Opener Each. So you got a JK and moved your license plate and now have an unsightly hole. MBO's license plate mount cover to the rescue!
|
|
|
|
|
Copyright © 1999-2021 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |