Class D, 70W x 2 Zone Amplifier

FUSION's Marine Zone Amplifier is designed to support the multi-zone technology. The Zone Amplifier is small, enabling discrete installation and when combined with the Marine Stereo Unit provides the platform for a True multi-zone audio system.

Why Do I Need A Zone Amplifier?

A Marine Zone Amplifier is needed if you are planning a multi-zoned system, comprising of three or four zones.

FUSION's Marine Stereo Units have the capability to run up to four pairs of speakers. You will also need to install a Marine Zone Amplifier if your sound system has more than four pairs of speakers.

Features:

• 2 Channel
• Class D
• 70W x 2
• 2 Ohm Stable
• Water resistant design
• Conformal coated PCB
• Audio detect selectable function the amplifier turns on when audio is detected and goes to sleep / low power mode when audio is not present
• Selectable high pass/ full range setting
• Variable high pass filter
• Small and discrete size: 128 x 78 x 51mm
• High Pass Crossover: 60Hz-600Hz
• Operating Range: 10-16V DC
• Max Power Rating (Watts): D-Class 70W
• Ratings per channel: 20W RMS @ 4 ohms per channel: 33WRMS @ 2 ohms per channel

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

MS-AM504 4-Channel Marine Amplifier - 500W 

Features:

• Marine Grade Chassis - Stainless steel end caps and bottom plate provide a stunning finish with added environmental protection.
• Heat Sink Technology - Heat sink technology transfers heat more efficiently and offers more thermal stability for maximum component reliability.
• Class-AB Design - The 500 Watt 2-Ohm stable (per channel) design ensures clean and powerful amplification of the input signal,enough to rock the boat.
• Conformal Coated Circuitry - Provides added protection from salt air and moisture to ensure maximum product life.
• RCA Line Out - A pass through RCA output enables linking of multiple amplifiers for enhanced system performance.
• 4 Channels - Capable of powering 4 speakers, a sub and a pair of speakers or 8 speakers in parallel (2 speakers per channel in parellel @ 2 Ohms).

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

MS-AM402 2 Channel Marine Amplifier - 400W 

Features:

• Marine Grade Chassis - Stainless steel end caps and bottom plate provide a stunning finish with added environmental protection.
• Heat Sink Technology - Heat sink technology transfers heat more efficiently and offers more thermal stability for maximum component reliability.
• Class-AB Design - The 400 Watt 2-Ohm stable (per channel) design ensures clean and powerful amplification of the input signal,enough to rock the boat.
• Conformal Coated Circuitry - Provides added protection from salt air and moisture to ensure maximum product life.
• RCA Line Out - A pass through the RCA output enables linking of multiple amplifiers for enhanced system performance.
• 2 Channels - Capable of powering 2 speakers, a sub (bridged) or 4 speakers in parallel.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

HYDRO Full Range Digital Marine Monoblock AMP - 1200W

Whether you are the type of audio enthusiast that likes to hit the open road on his bike, ride the rough trails on your side by side, or cruise the open waters, you are going to need a powerful and waterproof rated  amp that has a small footprint and also make great power. 

DS18 has a line just for the job with the NXL series of amplifiers to power your whole system. This Monoblock amplifier helps you accommodate for all your different speaker setups without having to look further. Being a full range amps, these can be run on subs, mids, or tweeters because of the internal design of the amp. 

All units have stable and reliable 4-layer PCB layouts, IPX67 rated for power sports, has an ultra-compact size for easy installation, and has audio precision quality control verification.

Technical Specifications:

• Number of Channels - 1
• Frequency Response - 20Hz - 20KHz
• 2 Ohm RMS Power (14.4V) Per Channel - 1 x 600W
• 4 Ohm RMS Power (14.4V) Per Channel - 1 x 400W
• 4 Ohm RMS Power Bridge (14.4V) Channel - N/A
• Input Sensitivity - 0.2-5V
• Low Pass Filter - 40Hz - 3KHz
• Signal-to-Noise Ratio - >95dB
• Product Dimensions: (L x W x H) - 215 x 125 x 42mm

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

• Accepts line level or speaker level inputs
  
• Powers up to 4, 4 Ohm speakers
  
• Separate waterproof Volume control (10' lead)
  
• Use to add additional loudspeakers to a current audio system
  
• Use to provide amplification for a separate audio zone
  
• Use as a stand-alone system amplifier for any audio source

• Speaker Impedance: 2-8 ohm
  
• Output Power 2ohm load: 25W RMS/Channel
  
• Output Power 4ohm load: 15W RMS/Channel
  
• Frequency Response: 20Hz-20kHz
  
• Operating Voltage: 13.8V DC (10V-16V
  
• Idle Current (no signal): 10mA
  
• Maximum Current Draw (full power): 7 amps
  
• Remote Wire Current: 4mA
  
• Approximate Length: 4-7/8" (124mm)
  
• Approximate Width: 4-3/16" (106mm)
  
• Approximate Height: 1-9/16" (39mm)
  
• Weight: 0.94lbs
  
• Volume Control Cable Length: 114"

Battery Power Cord - 7'

*only works with MTC

The Battery Power Cable allows you to connect your MTC to an additional battery. Includes inline 5 amp fuse to defend against battery shortage.

Features:

• 7' Power Cable
• 5 Amp Inline Fuse

Wired Infrared Motion Sensor

The Visonic 360 Ceiling Dualtech motion sensor offers robust protection against theft. Simply mount this sensor in a cabin or above the main entryway, and receive notification in the event of unauthorized entry. The sensor can also be programmed to sound an audible alarm. Featuring a sleek, compact, and elegant design, the sensor blends seamlessly into any décor. Visonic technology assures high reliability, false alarm immunity, and 360-degree coverage. Ideal for monitoring unexposed areas such as pilothouse, galley, cabin, etc.

Specifications:

• Dimensions: 3.37in (diameter) 1in (depth)
• Ceiling Mount
• Range:  360° detection pattern with floor coverage up to 36ft
• Supply Voltage: 9-12V
• Not recommended for use on weather/exposed decks
• Works with MTC and Siren 3 Pro

Wired Micro ePIR Motion Sensor

The Micro ePIR motion sensor provides similar functionality as the Visonic Duo 240  Ceiling Dualtech in the most compact and hard to detect package available. An ideal solution for monitoring a boat’s main entryway or corridor. Install on any wall or bulkhead for a well concealed layer of security. The sensor will push an alert to the boat owner upon unauthorized entry and can be programmed to sound an audible alarm.  

Specifications:

• Dimensions: 1.75in (diameter) 2.5in (depth) 6in (wire)
• Flush mount (2.5in depth behind mounting point)
• Range:  25ft/50°
• Adjustable backing plate
• Supply Voltage: 9-12V
• Not recommended for use on weather/exposed decks
• Works with MTC and Siren 3 Pro

Wired Shore Power Sensor Plug

The Shore Power Sensor Plug allows boaters to monitor system-critical shore power from anywhere. Receive an alert in the event that shore power is lost and avoid costly system shutdown. The Shore Power Sensor Plug is ideal for larger vessels relying on external power sources to run critical systems while on the dock.

Specifications:

• Dimensions: 3ft (wire) 2.5x1.5in (body)
• Standard AC to DC adapter, 3V DC output
• Plugs into AC outlet
• Works with MTC and Siren 3 Pro

High Water Alarm Panel

Replacement panel for LevelGuard High Water Alarm.

MA704 4 Channel Marine Amplifier 

The weather-resistant and high-performance JBL Marine amplifiers deliver impressive power from a compact chassis designed to withstand outdoor environments. Available with 4-channel and 5-channel outputs. JBL Marine amplifiers incorporate our latest amplifier topology that includes selectable all-, high-, or low-pass crossovers with variable electronic frequency adjustment for precision system tuning. Engineered for harsh marine conditions, with power and performance to meet the needs of any outdoor audio system, JBL Marine amplifiers are the perfect match for all of your JBL marine products. 

What's In The Box?

• 1 amplifier
• Stainless steel mounting hardware
• Rubber inserts
• 4 High-level input adapters
• 2 spare fuses
• 2 2-color brand stickers
• Quick start guide

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Wired Magnetic REED Switch

Magnetic reed switches are used to report unauthorized entry into a main cabin through a door or external hatch. Reed switches can be connected in series to monitor multiple entry points, providing secure protection against theft. In the event of unauthorized entry, the switches will trigger an entry alert to the boat owner, and can also be configured to sound an audible alarm on the boat.

Specifications:

• Dimensions: 1x1in (2-part body, 0.5x1in each) 12in (wire)
• Screw mount and adhesive mount included
• Grounds directly to security input
• Works with MTC and Siren 3 Pro

HYDRO Full Range Digital Marine 5-Channel AMP - 1600W

Whether you are the type of audio enthusiast that likes to hit the open road on his bike, ride the rough trails on your side by side, or cruise the open waters, you are going to need a powerful and waterproof rated  amp that has a small footprint and also make great power. 

DS18 has a line just for the job with the NXL series of amplifiers to power your whole system. This 5 channel amplifier helps you accommodate for all your different speaker setups without having to look further. Being a full range amps, these can be run on subs, mids, or tweeters because of the internal design of the amp. 

All units have stable and reliable 4-layer PCB layouts, IPX67 rated for power sports, has an ultra-compact size for easy installation, and has audio precision quality control verification.

Technical Specifications:

• Number of Channels - 5
• Frequency Response - 20Hz - 20KHz
• 2 Ohm RMS Power (14.4V) Per Channel - 4 x 125W+300W
• 4 Ohm RMS Power (14.4V) Per Channel - 4 x 80W + 200W
• 4 Ohm RMS Power Bridge (14.4V) Channel - 2 x 250W + 300W
• Input Sensitivity - 0.2-5V
• Low Pass Filter - 40Hz - 3KHz
• Signal-to-Noise Ratio - >95dB
• Product Dimensions: (L x W x H) - 192 x 125 x 42mm

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

BANSHEE™ Alarm Padlock

Protect Your Boats, Trailers and Property

The BANSHEE™ is an alarm-equipped padlock for protecting any valuable item, boat or trailer from theft. When tampered with the alarm "scream like a Banshee" warding off potential thieves.

Vibration-activated 110 Decibel Alarm Screams Like A Banshee When Activated Can Be De-Activated For Trailering Fits Most Trailer Couplers Weatherproof.

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Siren Marine Audible Alarm

The Siren Marine audible alarm produces a powerful beeping sound (105 decibels). The alarm can be connected to one of the outputs on the MTC, which will allow it to be turned on and off from the "switching" section of the Siren Marine App. It can also be mapped to specific inputs (such as a motion sensor) in the app and programmed to turn on automatically.

Features:

• Automatically adjusts to a supply voltage range of 12-80V
• Waterproof housing with epoxy embedded electronics
• Wiring is required to any 12V-80V DC power source
• Easy-to-install universal mounting bracket with slotted holes
• Requires connection to MTC

Specifications:

• Material: Heavy-duty plastic housing
• Waterproof: Yes
• Voltage: 12V-80V
• Power: 10W
• Current: 0.5A
• Length: 3.9 in (including bracket)
• Width: 1.5 in
• Height: 2.57 in
• Volume: 105 +/- 3dB

HYDRO Full Range Digital Marine 4-Channel AMP - 800W

Whether you are the type of audio enthusiast that likes to hit the open road on his bike, ride the rough trails on your side by side, or cruise the open waters, you are going to need a powerful and waterproof rated  amp that has a small footprint and also make great power. DS18 has a line just for the job with the NXL series of amplifiers to power your whole system. This 4 channel amplifier helps you accommodate for all your different speaker setups without having to look further. Being a full range amps, these can be run on subs, mids, or tweeters because of the internal design of the amp. All units have stable and reliable 4-layer PCB layouts, IPX67 rated for power sports, has an ultra-compact size for easy installation, and has audio precision quality control verification.

Technical Specifications:

• Number of Channels - 4
• Frequency Response - 20Hz - 20KHz
• 2 Ohm RMS Power (14.4V) Per Channel - 4 x 150W
• 4 Ohm RMS Power (14.4V) Per Channel - 4 x 150W
• 4 Ohm RMS Power Bridge (14.4V) Channel - 2 x 300W
• Input Sensitivity - 0.2-5V
• Low Pass Filter - 40Hz - 3KHz
• Signal-to-Noise Ratio - >95dB
• Product Dimensions: (L x W x H) - 245 x 25 x 42mm

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

120V AC Shore Power Relay

The AC Shore Power Relay is used to detect presence and loss of AC shore power. The relay is meant to be hardwired directly to your AC distribution panel. This relay is the hard wired alternative to the Siren Marine Shore Power Plug Sensor.

Specifications:

• Dimensions: 1.5x0.75x1.19in (box) 11.3in (wire)
• Relay may be energized by one of three input voltages: 24VDC, 24VAC, or 120VAC.
• Input voltages are polarity-sensitive and diode-protected.
• Relay contains a red LED which indicates when the relay coil is energized.
• Relay is required to monitor shore power off of your AC panel.
• Works with MTC and Siren 3 Pro

Wireless Bilge Pump Sensor

*works with MTC only

The Wireless Bilge Pump Sensor monitors bilge pump activity, including run time and daily cycles. Attach the Bilge Pump Connector to the bilge pump and plug the other end into the Wireless Module. Link the module to the MTC and receive alerts if the bilge pump exceeds a preset run time or cycle counts.

Includes: 

• Wireless Sensor Module 
• Bilge Pump Connector 
• 3 feet of wire
• Wireless Sensor Range from MTC is 150' @ 900MHz

PAM4 Wired DC Relay

The Siren Marine DC Accessory Relay allows users to control any 12v onboard devices, such as A/C, deck or spreader lights, sirens, or strobe lights.

• Dimensions: 1.5x0.75x1.19in (box) 11.3in (wire)
• Relay may be energized across a wide voltage range from 9VDC to 32VDC.
• Ideal for 12VDC and 24VDC circuits.
• 20mA operating current is constant across the operating range.
• Input voltages are polarity-sensitive and diode-protected.
• Relay is required to power or switch 12V systems that draw more than 1 Amp via the internal outputs of the MTC.
• Works with MTC and Siren 3 Pro

ZigBoat™ Starter Kit System - Gateway, Battery, Door/Porthold & Flood Sensor

The 100% wireless remote system for monitoring and interacting with your boat via the free App. No monthly fees or subscriptions. This kit contains a Gateway, a Porthole/Door sensor, a Battery sensor, a Bilge Flood sensor, and long life batteries, up to 5 years, ensuring safety and peace of mind.

ZigBoat™ is an innovative ZigBee/WiFi wireless system for monitoring and interacting with your boat either remotely or while on board ensuring safety and peace of mind with no monthly fees or subscription. The ZigBoat™ consists of a core module (Gateway) and a series of standard and optional sensors that can be added to your specific needs. Thanks to ZigBee and Wi-Fi wireless technologies, which have direct communication with onboard sensors without the need for a cloud, ZigBoat™ sends real-time push notifications when critical events occur. Using the ZigBoat™ app, you can check boat information that is being monitored by the system.

This kit contains a Gateway, a Porthole/Door sensor, a Battery sensor, a Flood sensor, and batteries for sensors:

Gateway

It is the core module of the ZigBoat™ system. It’s an open platform that can be integrated with unlimited ZigBoat™ additional sensors and features. If connected to the internet  (for example your weBBoat 4G Plus or the 3G USB dongle or a local WiFi), sends you push notifications on your mobile device.

Porthole/Door Sensor

You will receive alerts in case of opening and closing on door and portholes on your boat.

Battery Sensor

Monitor battery voltage.

Bilge Flood Sensor

Be instantly informed if the boat is taking on water. Moreover, the Flood Alarm has a built-in siren that will sound when water is detected.

ZigBoat™ is...

ZigBoat™ is easy to install and use. No cable needed. Just Plug & Play for wireless remote control & monitoring of your boat

Based on WiFi and ZigBee wireless technologies for fast and easy connection with the onboard sensors and managed by the ZigBoat™ iOS or Android App

The ZigBoat™ gateway uses direct, encrypted and real-time Peer-to-Peer connection platform to communicate with your mobile devices (smartphone and tablet) and have boat control anytime and anywhere: With no cloud, ZigBoat ensuring 100% privacy

ZigBoat™ offers several sensors and features to meet your specific needs, quickly and easily manage and configure via the App. The system can be integrated and expanded with unlimited additional sensors

WARNING: This product can expose you to chemicals including LEAD which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Tank Monitor 300/400 Interface Module

Replacement interface module for LevelGuard Tank Monitor 300 Kit.

Shore Power Relay - 240V

The 240VAC Shore Power Relay is used to detect presence and loss of AC shore power. The relay is meant to be hardwired directly to your AC distribution panel. This relay is the hard wired alternative to the Siren Marine Shore Power Sensor Plug for boats with 240VAC systems.

Features:

• Coil Voltage: 240VAC
• Contact Current: 10A
• Works with MTC and Siren 3 Pro

JAHD240BT 80W 2-Channel Bluetooth Amplifier

The waterproof JAHD240BT is on the forefront of technology with integrated Bluetooth technology allowing users to stream their audio content using a Bluetooth enabled device. Now, users can take their personal music library with them on all of their adventures. To pair the device, simply press and hold the button for about four seconds to place the JAHD240BT in pairing mode. It will remain in pairing mode for two minutes, and the blue LED will flash quickly. With a Bluetooth enabled device search for, and connect to the amplifier to complete pairing. All playback and volume options are controlled by the users Bluetooth enabled device. The unit also deploys 80 watts maximum power giving your audio system plenty of fire power.

Features:

• 80 watt max power (40 watt RMS)
• Bluetooth audio (AVRCP, A2DP)
• Waterproof (IPX6)
• Illuminated program button
• 4 Ohm - 8 Ohm stable
• Operating voltage: 10-18VDC
• Frequency response: 20Hz - 20KHz
• Red LED power indicator
• Epoxy potted encolsure
• Corrosion resistant (ASTM B117)

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

Tank Monitor 400 Panel

Replacement panel for LevelGuard Tank Monitor 400 Kit.

Tank Monitor 300 Panel

Replacement panel for LevelGuard Tank Monitor 300 Kit.

M4555A 5 Channel Marine Amplifier 

The weather-resistant & high-performance Infinity Marine amplifiers deliver impressive power from a compact chassis designed to withstand outdoor environments. Available with 4-channel and 5-channel outputs. Infinity Marine amplifiers incorporate our latest amplifier topology that includes selectable all-, high-, or low-pass crossovers with variable electronic frequency adjustment for precision system tuning. Engineered for harsh marine conditions, with power and performance to meet the needs of any outdoor audio system, Infinity Marine amplifiers are the perfect match for all of your Infinity marine products. 

What's In The Box?

• 1 amplifier
• Stainless steel mounting hardware
• Rubber inserts
• 4 High-level input adapters
• 3 spare fuses
• 2 2-color brand stickers
• Quick start guide

Features:

• Compact size - Infinity Marine amplifiers feature a slim chassis and a small footprint to allow for installation in tight spaces
• High- and low-level inputs - Speaker-level and low-level inputs let Infinity Marine amps integrate with just about any audio input.
• Selectable Output and Variable Adjustment Crossovers - Infinity Marine amps feature selectable all-, high-, or low-pass crossovers with variable electronic frequency adjustment to allow for fine-tuning multiple system configurations.
• Product Value - Infinity power and performance at an affordable price point
• Cosmetic Appeal - Product family look and feel to meet the needs of our Infinity customers
• Conformal-Coated PCB - Infinity Marine amplifiers are engineered to withstand harsh marine conditions, with fully “marinized” circuit boards to ensure flawless power delivery, year after year
• Variable Crossovers - Onboard 12dB electronic crossovers, with selectable full-range, high-pass & low-pass switching, provide tuning options for systems of any size
• Big Dynamic Power - Output power is perfectly matched to meet the needs for your Infinity marine products

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

MA4505 5 Channel Marine Amplifier 

Weather-resistant & high-performance marine amplifier

The weather-resistant & high-performance JBL Marine amplifiers deliver impressive power from a compact chassis designed to withstand outdoor environments. Available with 4-channel and 5-channel outputs. JBL Marine amplifiers incorporate our latest amplifier topology that includes selectable all-, high-, or low-pass crossovers with variable electronic frequency adjustment for precision system tuning. Engineered for harsh marine conditions, with power and performance to meet the needs of any outdoor audio system, JBL Marine amplifiers are the perfect match for all of your JBL marine products.

Features:

• 1 amplifier
• Stainless steel mounting hardware
• Rubber inserts
• 4 High-level input adapters
• 3 spare fuses
• 2 2-color brand stickers
• Quick start guide

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

• Maximum power output: 80 watts (40 watt RMS)
  
• Bluetooth streaming audio (A2DP)
  
• Waterproof (IPX6)
  
• Illuminated program button
  
• 4 Ohm-8 Ohm stable
  
• Operating voltage: 10 @ 18VDC
  
• Frequency response: 20 Hz @ 20 KHz
  
• Epoxy potted enclosure
  
• 10 amp fuse in waterproof holder
  
• Corrosion resistant (ASTM B117)
  
• UV resistant (ASTM D4329)

• Max power handling: 30 watts
  
• Waterproof
  
• Frequency: 79Hz, 20kHz
  
• Tweeter type: Mylar/Whizzer
  
• Sensitivity: 91dB
  
• Magnet: 2.9 oz.
  
• ASTM B117 Salt spray exposure standard compliant
  
• ASTM D4329 UV exposure standard compliant

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

• 4 Channel Class D Power Amp
  
• 2 ohm stable stereo outputs
  
• Bridgeable outputs
  
• Variable input level controls for each pair of channels
  
• Variable High-pass, Low-pass and All-pass crossover
  
• Variable Bass Boost circuit
  
• Thermal and overload protection circuitry
  
• Gold-plated RCA jacks and terminals

• Power Supply Voltage: 11-16 VDC
  
• Idling Current: 0.8A
  
• Idling Current when off: <0.001mA
  
• Output Power (RMS)@14.4V/4ohms: 125W x 4CH
  
• Output Power (RMS)@14.4V/2ohms: 200W x 4CH
  
• Output Power (max)@14.4V/4ohms: 250W x 4CH
  
• Output Power (max)@14.4V/2ohms: 400W x 4CH
  
• Fuse Rating: 25A x 3
  
• Dims (LxWxH) inches: 10-7/8" x 6-3/4" x 1-7/8" (275mm x 170mm x 46mm)

• 4-Channel Amplifier
  
• Max power output: 760W
  
• Designed to meet CEA-2006 test standards
  
• High current bi-polar output transistors
  
• Compact design allows great flexibility in mounting
  
• MOSFET power supply
  
• Built-in low-pass and high-pass crossover filters for bi-amplifying
  
• Channel mode selector switch- 4, 3 and 2 channel
  
• Full range option
  
• Green operation and red protection LEDs
  
• Protection circuit that safeguards against short circuits, DC-offset and thermal overload
  
• Variable bass EQ 0-12 dB at 45 Hz
  
• Overall Dimensions: 9"W x 2.5"H x 12.5"L

WARNING: This product can expose you to chemicals which are known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

SirenSat Offshore Antenna with 2M Power Cable*

*Requires SirenSat Offshore Subscription (sold separately)

Using the Globalstar Network of Satellites, the SirenSat Offshore Antenna allows users to track their boat, even after it leaves cellular coverage.  With Global coverage. boat owners who keep their boats in theft-prone areas, can now easily report the vessel location worldwide.   Plus, Global Tracking satisfies most insurance requirement for boats with multiple outboard engines.

Features:

• Satellite technology: Global LEO Satellite operation using the Globalstar Simplex Data Network
• Checks in every 15-30 minutes
• Includes 2M power harness to connect to 12V power supply
• Features geo-fencing capability
• Global coverage, non-dependent on cellular connection
• Works with MTC and Siren 3 Pro