A necessity for wind protection. Provides do-it-yourself protection for any storage building. May be used to anchor fences, tents, trees, boats, carports, antennas, airplanes, pool covers and playground equipment. Includes 30" eye anchors with 4" helix, 4 -1/8" galvanized clamps and 60-1/8" galvanized aircraft cable. Boxed. This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
POST FLOOR FLANGE
For surface mounting of Newel post
FF125 1-1/4 IN. NEWEL POST FLANGE
SIZE:1-1/4"
|
PACKAGED WIRE
Carded dispenser packs of wire
In various gauges and types
Features award-winning dispenser package
123121 22GA 75 FT. DK ANNELD WIRE
SIZE:22 Ga. 75 Ft.
DESC:Dark Annealed
|
CENTER HANGER SUPPORT
Use with fully extended 72" & 96" rods
Anochrome finish
29201 CTR SUPT/KV2 RODS
|
This item can NOT be shipped to these states CA
EARTH ANCHOR Steel earth anchor Screws into ground with bar or pipe Use to secure items firmly in position 811330 3 IN. X30 IN. EARTH ANCHOR SIZE:30" ROD/PLATE:7/16" x 3" |
1175BC HEAVY-DUTY BLACK CORNER PLATES
Used to reinforce 90 degree angles by -
applying to the side of the angle
Slots for 5/16" carriage bolt
Reinforce a variety of joints, seams & cracks
Black powder coat finish for weather resistance
Boxed loose
1175BC 6.5 1/8 BL CNR PLATE
SIZE:6.5"x 1.5"x 1/8"
FINISH:Black
|
G90 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the paper catalog R7 Refer
ence Pages.
LIGHT-DUTY
20 Gauge - 1-9/16"W x 1-1/2"D
Joist Size=2Ht In=3
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
Secures batt-type insulation in place between joists. Chisel cut ends dig into joists for permanent holding. Easy to install in hard-to-reach crawl spaces. Pushes into place. Overall length is 1/2" less than over center joist spacing. 13 Gauge.
BULK
Joist Spacing OC=16
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
Simplifies stair construction and eliminate the need to calculate and notch stair stringers. Stronger and safer than wood blocking, and the angle and fasteners are hidden from view. Use the SCA9 for single 2x10 stair treads and SCA10 for double 2 x 6 stai
r treads. Requires 1/4" x 1-1/2" lag bolts. Meets ICC-ES ESR-1280, FL11664 and L.A. City RR25749 codes. For additional information on installation, please see USP Lumber Connectors charts in the paper catalog R7 Reference Pages.
450 LB. ALLOWABLE DOWNLOAD
10"L x 1-3/8"W - 12 Gauge
Finish=Triple Zinc
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
This item can NOT be shipped to these states CA
GRID HANGING WIRE Will not scratch Use with lag screws & nails 5010 100 FT. GRID HANGING WIRE SIZE:100' Coil |
Color=Red
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
MASONRY ANCHOR
Use to anchor to solid masonry
MA100 MASONRY ANCHOR 4/CD
DESC:4 ct Card
|
TDX SERIES HOLDOWNS
Features formed, self-jigging design
G90 galvanized finish
Triple-zinc for ACQ treated wood
TDX2-TZ 8 IN. TIE DOWN
SIZE:8.5x 2.06x 2.75"
FINISH:Triple-Zinc
|
Speed prongs designed to temporarily position hangers on headers for more convenient nail fastening. G-185 galvanizing finish. Meets ICC-ES ESR-1781, FL43285, Dade county, FL11-0510.01 and L.A. City RR25843 codes. For additional information including allo
wable loads and fasteners, please see USP Lumber Connectors charts in the paper catalog R7 Reference Pages.
TRIPLE ZINC FOR ACQ PRESSURE TREATED LUMBER
18 GAUGE - 1-9/16"W x 1-1/2"D
Joist Size=2 x 6Ht In=4-1/2
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
PACKAGED WIRE
Carded dispenser packs of wire
In various gauges and types
Features award-winning dispenser package
123107 24GA 325 FT. GALV WIRE
SIZE:24 Ga. 250 Ft.
DESC:Galvanized
|
Replace wood blocking on roof sheathing. Tight fit for positive installation. Embossed dimples provide 1/8" gap needed to prevent panels from popping up as sheathing expands. G60 galvanizing finish. 20 Gauge - Boxed.
Size In=15/32
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
For securing mudsills and framing into concrete slabs. Do not rely-on for securing concrete sections together between cold joints. Features split flange for nailing to both mudsill and stud for greater framing versatility. Use a minimum of 2 anchors per m
udsill within 12" of the end of each section. Meets ICC-ES ESR-2787 codes For additional information including allowable loads and fasteners, please see USP Lumber Connectors charts in the paper catalog R7 Reference Pages.
16 GAUGE - FOR 2 X 4-6 PLATE
11-1/8"H - For ACQ Pressure Treated Lumber
Finish=Triple Zinc
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA Light-duty Series require 10d nails for installation. Designed for use with 1-1/2"W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. For additional inform
ation including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the paper catalog R7 Reference Pages.
18 Gauge
Wdth x Lgth In=1-1/4 x 36
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
1184BC RECTANGULAR MENDING PLATE
Used for attaching, connecting, aligning, -
and splicing materials
Slots for 5/16" carriage bolt
Chamfered corners provide decorative look
Use for heavy-duty reinforcement of joints,-
seams and cracks
Black powder coat finish for weather resistance
Boxed loose
1184BC 4.7X3 1/8 BL MEND PLATE
SIZE:4.7"x 3"x 1/8"
FINISH:Black
|
Typically used with 2" OD pipe to reinforce joists, plates, studs, or rafters which have been drilled or notched during construction. Not for total member replacement in structural applications. G90 galvanized finish. Single stud requires ten 10d x 1-/12
fasteners and double stud requires twelve 10d and 2" maximum hole size.
16 Gauge - Single Stud
Wdth x Ht In=1-9/16 x 5
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
20 Gauge
Wdth x Lgth In=1-1/4 x 9
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
Connects wood framing to resist tension forces. G90 galvanizing finish. LSTA Light-duty Series require 10d nails for installation. Designed for use with 1-1/2"W framing members, including I-Joist flanges. Meets ICC-ES ESR-1781 codes. For additional inform
ation including allowable loads and number of fasteners, Please See USP Lumber Connectors charts in the paper catalog R7 Reference Pages.
20 Gauge
Wdth x Lgth In=1-1/4 x 24
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
NO-DRILL RAIL FASTENER KIT
Standard-type no-drill, adjustable connector
Attaches rails to posts, columns & walls
1 package required for each rail section
Kit includes 4 fasteners w/nuts & bolts
ND125 1-1/4 IN. CONNECTORS
SIZE:1-1/4"
|
Secures posts to concrete in light-duty and medium-duty applications such as patio covers, carports or decks. Formed, one-piece design includes embossing for additional lateral strength. Not for fence posts or other unrestrained (not fixed or fastened at
top) applications. Not designed to resist overturning (moment) loads. Requires (2) 1/2" HDG bolts or (12) HDG nails for fastening to post. Meets SBCCI, BOCA - NER 530 & NER 608, ICBO 5700, ICBO 2039, ICBO 5531, FL821, FL822, L.A. City RR 25337, and DSA P
A-076 codes. For additional information including allowable loads and fasteners, Please See USP Lumber Connectors charts in the paper catalog R7 Reference Pages.
TRIPLE ZINC - FOR ACQ PRESSURE TREATED LUMBER
3-1/2"W x 3-1/4"L x 4-3/4"H
Post Size In=4 x 4
This item cannot be shipped to APO/FPO addresses. Please accept our apologies
|
Stainless Steel Ties 200# 14.2"L x .18W - Stainless Steel Ties are perfectly suited to hostile environments.Stainless Steel Ties 200# 14.2"L x .18W features include:
Below is more info on our Stainless Steel Ties 200# 14.2"L x .18W Tensil Strength (LBS.): 2#Length: 14.2'' Width: .18'' Thickness: .1'' Max Bundle Dia: 4'' Bag Qty: 1 Master Bag Qty: 4 This item does not ship to APO/FPO addresses. |
RT3A REVERSIBLE HURRICANE & SEISMIC ANCHOR
Reversible, double-plated design
Ties trusses & rafters to top plates
May be used to tie wood framing members
Resists uplifts & lateral forces
RT3A HURRICANE/SEISMIC ANCHOR
SIZE:4.5"x1.44"x #18
FINISH:Galvanized
|
This item can NOT be shipped to these states CA
BAR TIE TWISTER HANDLE Convenience and speed when tying double loop- wire ties Wooden handle with steel twister 80740 BAR TIE TWISTER HANDLE |
RT7A DOUBLE PLATE RAFTER TIE
Truss/rafter to double plate installation
Adds increased resistance to wind uplift -
as well as lateral forces
Section lengths; 4" and 2-7/16"
6-1/2"L x 1-1/2" width
Section lengths; 4" and 2-7/16"
RT7ATZ HURRICANE ANCHOR
SIZE:1.5"x 6.5"x #18
FINISH:Triple-Zinc
|
TB2527 14CT SM D RING HANGER
|
SINGLE SLOT ROOF TRUSS TIE
Single slotted design roof truss tie
Allows truss to deflect without imposing -
load on wall below
18 gauge steel construction
G90 galvanized
TR1 SGL SLOT ROOF TRUSS TIE
SIZE:1.25"x2.75"x #18
DESC:Galvanized
|
V116 SERIES T PLATE
Designed to join two pieces of wood together -
at 90 degree angles
For screens and frames
Hot-rolled steel - zinc plated
Screw holes countersunk - screws included
2 plates per visual pack
V116 3X3 ZN T PLATE 2/PK
SIZE:3" x 3"
FINISH:Zinc Plated
|
|
|
|
|
Copyright © 1999-2021 BuilderDepot, Inc. Site Designed and Maintained by Inline Internet Systems, Inc. |