• Assorted butt connectors
  
• Ring, spade and male
  
• Female disconnects (18-10 AWG)

WARNING: This product can expose you to chemicals including di(2-ethylhexyl)phthalate (dehp) which is known to the State of California to cause cancer, birth defects or other reproductive harm. For more information go to P65Warnings.ca.gov.

• The 'Deluxe' version includes 10 fast-fit terminals for a quicker install
  
• Wateright Installation - Cables are quickly routed into the box through an IP66 elastomeric membrane, guaranteeing protection against water ingress.
  
• Mounting Bracket Included - Boxes can be fitted directly to the required mounting surface. A surface mounting bracket is also included to allow removal of the box for inspection if necessary.
  
  Picture shows optional IP67 Cable seal kit(SB-2G)

• The 'Standard' box provides 5 screw-down terminals
  
• Wateright Installation - Cables are quickly routed into the box through an IP66 elastomeric membrane, guaranteeing protection against water ingress.
  
• Mounting Bracket Included - Boxes can be fitted directly to the required mounting surface. A surface mounting bracket is also included to allow removal of the box for inspection if necessary.

200 Piece Terminal Kit - This Multi Piece Terminal Assortment has all the connectors and terminals you'll need.

200 Piece Terminal Kit features include:

• High impact reusable plastic box
• Multi piece terminal assortment contains ring and spade terminals, butt connectors & male and female disconnects
• Contains the following:
  • 4 pcs 10012 Ring Terminal 22-16 #6
  • 4 pcs 10014 Ring Terminal 22-16 #8
  • 4 pcs 10016 Ring Terminal 22-16 #10
  • 4 pcs 10032 Ring Terminal 16-14 #6
  • 4 pcs 10034 Ring Terminal 16-14 #8
  • 5 pcs 10036 Ring Terminal 16-14 #10
  • 4 pcs 10062 Ring Terminal 12-10#8
  • 6 pcs 10064 Ring Terminal 12-10 #10
  • 4 pcs 10066 Ring Terminal 12-10 1/4”
  • 4 pcs 10068 Ring Terminal 12-10 5/16”
  • 4 pcs 10112 Spade Terminal 22-16 #6
  • 4 pcs 10114 Spade Terminal 22-16 #8
  • 4 pcs 10116 Spade Terminal 22-16 #10
  • 4 pcs 10132 Spade Terminal 16-14 #6
  • 8 pcs 10134 Spade Terminal 16-14 #8
  • 7 pcs 10136 Spade Terminal 16-14 #10
  • 9 pcs 10162 Spade Terminal 12-10 #8
  • 16 pcs 10164 Spade Terminal 12-10 #10
  • 4 pcs 10166 Spade Terminal 12-10 1/4”
  • 11 pcs 10182 Butt Connector 22-18
  • 11 pcs 10184 Butt Connector 16-14
  • 9 pcs 10186 Butt Connector 12-10
  • 4 pcs 10214 Male Disconnect 22-16 .250
  • 4 pcs 10224 Male Disconnect 16-14 .250
  • 4 pcs 10232 Male Disconnect 12-10 .250
  • 5 pcs 10314 Female Disconnect 22-18 .250
  • 4 pcs 10322 Female Disconnect 16-14 .187
  • 11 pcs 10324 Female Disconnect 16-14 .250
  • 13 pcs 10332 Female Disconnect 12-10 .250
  • 4 pcs 10411 Female Insul Disconn 22-18 .250
  • 5 pcs 10412 Female Insul Disconn 16-14 .250
  • 4 pcs 10414 Female Insul Disconn 12-10 .250
  • 4 pcs 10415 Male Insul Disconn 22-18 .250
  • 4 pcs 10416 Male Insul Disconn 16-14 .250
• Terminals and Disconnects are cULus Listed
• Order Qty of 1 = 1 Terminal Kit

Below is more info on our 200 Piece Terminal Kit

High Temperature Butt Splice Terminals 22-18 AWG for extreme temperature applications

High Temperature Butt Splice Terminals 22-18 AWG features include:

• Applications Include: Electric space heaters, HVAC controls, Industrial automation, Commerical ovens and fryers & Industrial kilns
• Material: Nickel Plated Steel
• Temperature Rating: 900°F(482°C)
• Butted Seam
• Order Qty of 100 = 1 Bag of 100

Below is more info on our High Temperature Butt Splice Terminals 22-18 AWG

Push-In Wire Connectors 8 Pole Hanging Bag 25 Pack - These Easy Push Wire Connectors are Fast and Effective Alternative to Wire Nuts.

Push-In Wire Connectors 8 Pole Hanging Bag 25 Pack features include:

• Easy Push-In Wire Connectors are simple to install - instead of Twisting or Taping, simply Push Wires Into Contact Port to save you time and money
• Accepts Either Stranded or Solid Wire
• Low Wire Insertion Force allows fast, easy connections
• No-Twist Connection reduces repetitive motion fatigue
• Easy Push In Wire Connectors are Re-Useable, making changes easy and reducing waste of connectors
• Clear Housing for Visible Connection Confirmation
• Check Port for Continuity Testing
• Electrolytic Tin-Plated Internal Copper Bus for high conductivity
• Housing Material: Thermoplastic, UL 94V-2 flame retardant
• Current: 24A (VDE)
• Voltage: UL-600V, VDE-450V
• Working Temperature: 230°F (110°C)
• Wire Range: 12-22 AWG Solid conductor
• Color Coded according to # of poles
• cULus Listed
• Copper Wire Only
• (Bag 25 Pack) Order Qty of 25 = 1 Bag of 25

Below is more info on our Push-In Wire Connectors 8 Pole Hanging Bag 25 Pack

Above Ground Insulation Piercing Connectors Main 1/0-8 Tap 1/0-8 - Anyone can use our Above Ground Connector

Above Ground Insulation Piercing Connectors Main 1/0-8 Tap 1/0-8 features include:

• Connector Installs In Just Minutes Saving Many Man-Hours On The Job
• Eliminates Wire Stripping, Connecting & Taping of Split Bolts and Adding Inhibitor
• Above ground connector can be installed on Energized Circuits eliminating Power Shutdowns
• Overhead services - both insulated & bare mains, above grade URD services, street lighting, non-tension splicing & tapping, insulated replacement for split bolts, tapping without cutting the main, gutter taps.
• Double shear-head bolt guarantees correct torque tightening every time, ensuring a quality connection, & eliminating the possibility of hot spots, damaged wires or loose connections
• No cable stripping required, simply insert the jacketed cable into the entry port & tighten with a 1/2” 6 point socket
• Red Turbo spacer allows tap side to remain open while you hand tighten the above ground connector on the main wire (all models except 96102 & 96104)
• Blue Rubber Insert recreates insulation when used on bare wire. Used to avoid any damage on neutral messenger. (Only on Models 96106, 96110, 96112, 96114)
• The bolt and all external parts of the connector are completely isolated from energized parts and the bolt is covered by the plastic shear-head.  The installer has no contact at any point with an energized part.
• Can be installed on energized conductors, however, the tap must not be under load.
• Corrosion-free connection is good for hot, cold, damp, & salty connections.  Properly installed the connector seals water-tight. This is accomplished by a sealant tank, that during installation is compressed and forces sealant out to protect the connection from oxygen and water.  Copper teeth are tin plated, shell is high strength UV resistant thermoplastic insulating material, steel bolts are galvanized.
• The connector bodies are made from high-strength fiber-reinforced thermoplastic and galvanized steel bolts
• UL486B Listed for cu to cu, al to al, & cu to al; 600 Volt, 194°F (90°C) Rated, Meets ANSI C119.4 requirements
• Order Qty of 1 = 1 Piece

Below is more info on our Above Ground Insulation Piercing Connectors Main 1/0-8 Tap 1/0-8

Nylon Insulated Butt Splice Connectors 26-22 Awg - Nylon Insulated Butt Splice Connectors for electrical work.

Nylon Insulated Butt Splice Connectors 26-22 Awg features include:

• Nylon Insulated Butt Splice Connector Material: High Strength Electrolytic Tubular Copper
• Electro-Tin Plated for corrosion resistance
• Nylon Insulated Butt Splice Connector has Center Wire Stop Barrier
• Color Coded Insulation for easy identification
• Easy Entry Expanded Insulation eliminates strand “Hang Up”, increasing crimping rates and provides mechanical strain relief
• Maximum Electric Current: 26 AWG - 5.5 Amp, 24 AWG - 7 Amp, 22 AWG - 9 Amp, 20 AWG - 12 Amp, 18 AWG - 17 Amp, 16 AWG - 18 Amp, 14 AWG - 30 Amp, 12 AWG - 35 Amp, 10 AWG - 50 Amp
• 221°F(105°C) 600 Volts Max
• cULus Listed
• Dimension Measurements = Inches

Below is more info on our Nylon Insulated Butt Splice Connectors 26-22 Awg

Above Ground Insulation Piercing Connectors Main 4/0-2 Tap 2/0-6 - Anyone can use our Above Ground Connector

Above Ground Insulation Piercing Connectors Main 4/0-2 Tap 2/0-6 features include:

• Connector Installs In Just Minutes Saving Many Man-Hours On The Job
• Eliminates Wire Stripping, Connecting & Taping of Split Bolts and Adding Inhibitor
• Above ground connector can be installed on Energized Circuits eliminating Power Shutdowns
• Overhead services - both insulated & bare mains, above grade URD services, street lighting, non-tension splicing & tapping, insulated replacement for split bolts, tapping without cutting the main, gutter taps.
• Double shear-head bolt guarantees correct torque tightening every time, ensuring a quality connection, & eliminating the possibility of hot spots, damaged wires or loose connections
• No cable stripping required, simply insert the jacketed cable into the entry port & tighten with a 1/2” 6 point socket
• Red Turbo spacer allows tap side to remain open while you hand tighten the above ground connector on the main wire (all models except 96102 & 96104)
• Blue Rubber Insert recreates insulation when used on bare wire. Used to avoid any damage on neutral messenger. (Only on Models 96106, 96110, 96112, 96114)
• The bolt and all external parts of the connector are completely isolated from energized parts and the bolt is covered by the plastic shear-head.  The installer has no contact at any point with an energized part.
• Can be installed on energized conductors, however, the tap must not be under load.
• Corrosion-free connection is good for hot, cold, damp, & salty connections.  Properly installed the connector seals water-tight. This is accomplished by a sealant tank, that during installation is compressed and forces sealant out to protect the connection from oxygen and water.  Copper teeth are tin plated, shell is high strength UV resistant thermoplastic insulating material, steel bolts are galvanized.
• The connector bodies are made from high-strength fiber-reinforced thermoplastic and galvanized steel bolts
• UL486B Listed for cu to cu, al to al, & cu to al; 600 Volt, 194°F (90°C) Rated, Meets ANSI C119.4 requirements
• Order Qty of 1 = 1 Piece

Below is more info on our Above Ground Insulation Piercing Connectors Main 4/0-2 Tap 2/0-6